Posts

Receive Loudness Rating with ITU Real Speech Test Sequence

The purpose of this sequence is to measure the Receive Loudness Rating (RLR) following the ITU-T P.79 standard using a Head and Torso Simulator (HATS). First, real speech from the ITU-T P.501 standard is sent to the Device Under Test (DUT) speaker by an electrical interface. The HATS right ear captures the DUT‟s speaker response. SoundCheck calculates the frequency response and then RLR based on that recording.

More

Send Loudness Rating with ITU Real Speech Test Sequence

The purpose of this sequence is to measure the Send Loudness Rating (SLR) following the ITU-T P.79 standard. This sequence can be used with handsets, headsets, and conference call devices. First, real speech from the ITU-T P.501 standard is played out of a mouth simulator. The Device Under Test (DUT) microphone then captures the signal and transmits this back to SoundCheck. SoundCheck calculates the frequency response function in 1/3 octaves and calculates SLR based on that frequency response.

More

Hearing Aid Frequency Response Test Sequence

This sequence follows the ANSI S3.22-1996 standard method for testing the frequency response of a hearing aid. An equalized stepped sine sweep from 8 kHz – 200 Hz is played at a level of 60 dBSPL through the anechoic box speaker, and the output of the hearing aid is analyzed with the Heterodyne algorithm to produce a frequency response. Next, the HFA (High Frequency Average) is calculated by averaging the response values at three frequencies (1000, 1600, 2500 Hz). The HFA is then subtracted by 20 dB. Two post processing steps are used to find the upper and lower frequency points at which the response curve intersects this calculated value (HFA – 20 dB). These are the high and low frequency cutoff points.

More

Hearing Aid OSPL 90 Test Sequence

This sequence follows the ANSI S3.22-1996 standard method for measuring the OSPL curve, the HFA value, and the Max OSPL value for a hearing aid. An equalized stepped sine sweep from 8 kHz – 200 Hz is played at a level of 90 dBSPL through the anechoic box speaker, and a broadband response curve is analyzed through the hearing aid. Next, the HFA (High Frequency Average) is calculated by averaging the values at three frequencies (1000, 1600, 2500 Hz), and this value is checked with a limit step. The Max OSPL is calculated by finding the maximum point on the broadband response. A limit is also applied to this value.

More

Release Time Hearing Aid Test Sequence

This sequence follows the ANSI S3.22-1996 standard method for testing the release time of AGC (automatic gain control) hearing aids. A 2 kHz sine tone is played at 90 dBSPL for 1 second and then immediately drops to 55 dBSPL for 2 more seconds. A band limited time envelope (1.5-2.5 kHz) is created and then run through a post processing step, which calculates the release time. It does this by calculating the time it takes the device to stabilize within 4 dB of its steady level.

More

Loose Particles Sequence

This sequence demonstrates how to use SoundCheck to detect loose particle defects in loudspeakers. Loose particles typically reveal themselves as randomly spaced impulses, so they may not be detected when performing frequency based measurements such as THD, even though they can be clearly heard as undesirable artifacts. The loose particle algorithm, which is an available function in all analysis algorithms, analyzes a time waveform to detect these impulses. The user sets a customized threshold level for detection.

More

Complete Test Sequence

The purpose of this sequence is to perform a full suite of basic measurements for a loudspeaker. A 500 mV stepped sine sweep from 20 kHz to 50 Hz is played through the speaker and measured via two channels of the audio interface. A calibrated reference microphone is connected to one of the channels, and an impedance reference is connected to the other.

A HarmonicTrak™ analysis step analyzes the recorded waveform from the reference microphone, and outputs frequency response, THD, Rub & Buzz, and various harmonic curves. A second analysis step analyzes the waveform from the impedance reference and outputs a curve of impedance versus frequency. A post processing step is used to estimate the characteristics of the impedance curve and calculates the max impedance, resonance frequency, and the Q of the resonance peak.

More

Bluetooth Headset Test Sequence

The purpose of this sequence is to test a Bluetooth headset using a mixture of analog and digital channels. First, a Multitone stimulus is created with SoundCheck, played back over the Bluetooth headset (at 8 kHz) and recorded by a head and torso simulator’s ear (at 44.1 kHz). Then the same Multitone stimulus is played back through the head and torso’s mouth simulator (at 44.1 kHz) and recorded via the Bluetooth headset (at 8 kHz).

Due to inaccuracies of clock frequency, the Bluetooth device playback sampling rate is often slightly different than it is specified. Therefore, in SoundCheck, the Recorded Time Waveforms are frequency shifted to correct for the inaccurate sampling rate. The exact device playback sampling rate is displayed.

More

Amplifier THD+N Sequence

This sequence measures an audio amplifier’s Frequency Response, Gain, THD, THD+Noise, and Self-noise. It accomplishes this by playing a 1/3rd octave sine sweep through the amplifier. A HarmonicTrak™ analysis step calculates the fundamental frequency response curve as well as the distortion plots. The sequence then records and analyzes a spectrum of the amplifier’s self-noise.

More

Polar Plot (Linear X Turntable) Loudspeaker Sequence

This sequence measures the polar response of a loudspeaker in both the vertical and horizontal dimensions. It is designed to work with the Linear X turntable, and has all the necessary commands to automatically rotate it via RS-232. The sequence uses a log sweep stimulus with the Time Selective Response algorithm so that the measurements can be run in a non-anechoic environment. Note that the time window needs to be adapted to the user’s measurement space. The sequence plays the stimulus and measures at 10 degree increments from 0 to 180 degrees. This process is repeated with the speaker positioned horizontally. The two results are mirrored to display full 360 degree polar plots for each axis. A directivity index curve is also calculated for each axis and is displayed at the end of the test.

More