Installation Guide: AmpConnect 621 + SoundCheck
Get up and running with your AmpConnect 621 and SoundCheck in minutes! This step-by-step guide walks through installation, activating your license, hardware setup, and running a self-test to ensure everything is working correctly. We’ll also walk through a quick loudspeaker measurement so you can start testing right away!
Watch the video here:
Learn More about AmpConnect 621
-
- AmpConnect 621 Product Page: https://www.listeninc.com/products/audio-testing-hardware/ampconnect-621/
Video Transcript: Installation Guide: AmpConnect 621 + SoundCheck
Hi, I’m Jason from Listen. Today I’m going to show you how to install and configure your new AmpConnect 621 with SoundCheck. Before you start, make sure you have:
- Your hardware key
- Your AmpConnect 621 and the USB cable to connect it to the computer.
- Access to the internet to download the software, or a USB drive containing the installer
- The email you received with the “status’dat” license file. This was sent when the hardware was shipped. If you don’t have this – maybe you can’t find the email, or maybe it was sent to a colleague who placed the order, call or email us and we’ll re-send it right away.
Now, let’s install SoundCheck. If you’re already a SoundCheck user and you’ve just acquired new hardware, you can skip ahead to where we configure the hardware.
First insert the SoundCheck hardware key into one of your computer’s USB ports. The drivers for this key are included in the software installation, so we want it plugged in early.
00:30
Now let’s install the software. The download link is in the email with the license status.dat file. Again, if you need us to re-send this, please give us a call or email. I’ve already downloaded it, so it’s here…the setup executable.
Let’s click to install it… You may need to temporarily disable anti-virus or security settings..
If you’re on a Windows machine installing it for the first time, it may prompt you to re-boot to finish installing the LabVIEW Runtime engine – this is normal, and SoundCheck will resume automatically after the reboot.
Don’t forget to register your software and hardware – this will ensure you’re kept up to date with any new versions or software patches, and also ensure speedy support should you run into any issues that you need help with.
Now let’s open SoundCheck.
You can see it starts off in demo mode – that’s just because we haven’t activated the software yet. When you open SoundCheck, the setup wizard pops up automatically, and prompts us to locate our status.dat file… Make sure you’ve saved this somewhere you’ll remember on your computer. Note that this file is key-specific, so if you’re installing multiple systems, you’ll want to make sure you have the status file that matches the key for that system. Also, if you’re installing multiple systems, you can put all the license files in the same directory and SoundCheck will automatically select the status.dat file that matches the connected key. Make sure you select the “Current Folder” option instead of “Open” if you are doing this.
Next it prompts us to import settings from a previous version of SoundCheck. If this is your first time using SoundCheck, you can ignore this.
Now we’ll connect and configure our AmpConnect 621. If you have SoundCheck open, exit it – you want to have the 621 connected before you open SoundCheck.
Plug in the AmpConnect 621’s power cable. Then connect the 621 to your computer with the USB cable, and power it on.
Now open SoundCheck.
Because we plugged the unit in already, SoundCheck automatically recognizes the AmpConnect 621. If your device isn’t discovered, try disconnecting and reconnecting the USB cable and powering the device off and on. Now let’s configure it.
Select ‘Hardware’ from the setup menu and go to the hardware table. We’re on the “audio” tab at the top, and we can see all the input and output channels for the AmpConnect 621 have been automatically populated. Parameters such as the input and output peak voltage (Vp) values are stored on the device firmware and loaded automatically, so you don’t need to type them in. Before we save and close this, let me show you the hardware configuration. Here you can select the AmpConnect 621, hit ‘read settings’ and this is where you can see what the current settings are. After this is configured, every time SoundCheck starts up these settings will be set on the AmpConnect. For now we don’t need to change anything here as Self Test and Complete Test will configure this for us using message steps. This is good to know for when you are writing your own sequences, troubleshooting, or would like to assign a different start-up configuration. We’ll click ok, and hit ‘Save‘ to close the editor.
To finish off, we’ll run a self-test to make sure everything is communicating correctly. Go to File > Open
Navigate to the ‘Sequences\Calibration’ folder. I’m going to select ‘AmpConnect 621 Self Test 2 Channel’ because I’m just using two of the inputs on a 2 channel system; if you have an 8 channel or higher system, you can use the AmpConnect 621 self test below this one.
We get a document with more information about this sequence, I’ll just close that. And let’s hit the Green Start button – or you can use the F2 keyboard shortcut – to run the sequence.
This test configures the AmpConnect to internally loop back the outputs to the inputs, and it makes sure that it’s able to send and receive signals without relying on external cables or transducers. This can be used as a sanity check to make sure that everything in SoundCheck’s hardware table is set properly and there is no issue with the device.
And we can see, this unit has passed self-test. Now there’s just one more thing to note: here there’s a little note to alert us that if the latency is more than plus or minus one sample, the default needs adjusting. We can see our latency here is minus 2, so let’s just fix that.
We’ll go back into our hardware table and we’ll subtract 2 from our latency number and save that. Now let’s re-run the self test and we can see our latency is now within range.
Self-test is an important step – don’t skip it!
Now everything is configured we’re ready to make a measurement. Let’s do a quick demo.
I’m going to run a basic test on a loudspeaker.
You’ll need a measurement microphone to capture the response. Here I have an SCM microphone, I’ll connect this via a BNC adapter to mic input 1. And let’s connect my speaker to the amplifier output and power on…and check the speaker and microphone are correctly aligned. It’s that simple – now we’re ready to test.
SoundCheck comes with lots of pre-installed test sequences to get you up and running quickly.
Let’s open up the ‘Complete test using AmpConnect 621′ sequence from the Loudspeakers folder. You can see there’s an instructions document there if you want to learn more about the test.
Before we run the sequence, let’s double check our routing and signal paths. We can see here in the sequence editor that the acquisition step uses Mic 1, Amp 1, and Impedance 1 as our signal paths. SoundCheck automatically created these signal paths in calibration, and we can see here they are automatically set to the appropriate hardware channel. Now let’s hit run.
And there you can see, we’ve got measurements for frequency response, impedance, THD, and more from one sweep.
And that’s it. You are up and running. For more resources, visit the Listen support site or check the manuals included in your installation. And if you have any problems with your installation. We’re here to help – just give us a call or email support@listeninc.com.




