How to Measure: Haptics
SoundCheck is commonly used for measuring sound, but did you know it’s also useful for measuring vibration? This short demonstration walks you through how to measure vibration and haptic intensity, what hardware is required, how to configure that hardware with SoundCheck, and how to perform vibration level vs time and resonant frequency measurements.
Watch this Video Demo
Learn More about Measuring Haptics
- Haptic Measurement Sequence: https://www.listeninc.com/haptic-sequence/
Video Transcript: How to Measure Haptics
Usually we use SoundCheck to measure sound, but did you know that you can also use it to measure vibration? This is valuable if you have a device that produces tactile alerts as well as audible ones, like phones or watches, or even for evaluating seat vibrations that enhance low frequency playback in cars.
Let’s take a look.
The test setup is very similar to an audio measurement. The main difference is that instead of capturing sound with a microphone, we use an accelerometer. First I’m going to show you how we can use this to measure different vibration intensities on a phone, then I’ll show you the signatures produced by different ringtones on a watch.
To capture the vibration, I’ll use a B&K Type 4534 B accelerometer. I’ll connect this to input 1 on my AudioConnect 2 audio interface, which is connected via USB to the SoundCheck computer for our acquisition and analysis. The accelerometer requires IEPE bias, so I’ll set that on input 1 of my AudioConnect 2 in the hardware configuration. This is a TEDS accelerometer, and AudioConnect 2 is TEDS compatible, so I can simply read my calibration data from the accelerometer. If you’re using a different type of audio interface, you may need to manually calibrate it. If you want to know more about how to do this, check out our quick tip video on using accelerometers with SoundCheck.
First I’ll measure vibration intensity on a phone.
SoundCheck isn’t configured to control the vibration so I’ll do this manually. For this demo, I’ve downloaded an app called HapticsTouch that lets me customize the vibration pattern, and I’ve created three different intensity vibrations, high, medium and low. If you’re the phone manufacturer with full access to the device, you can control this directly from SoundCheck with a Python script or via TCP/IP. Other devices such as shakers can be excited by simply sending voltage directly from SoundCheck via a calibrated amplifier such as the one built into Listen’s AmpConnect 621.
I’ll attach the accelerometer to the front of the phone with sticky tack, making sure I have a secure connection.
Now I’ll run my SoundCheck sequence. It prompts me to start with the high intensity vibration, so I’ll just start that from my phone – that’s working – I can feel it – and say OK. It’s now making a 3 second acquisition to capture the vibrations. It’s got that – now it wants me to play the medium intensity, so I’ll start it and hit OK. And now the low intensity…
And here are our results…
We can see the acquired waveforms – that’s the raw data… our FFT spectra… level vs time… and resonant frequency of each intensity. If you’re testing in a production environment, you could use a golden unit to set limits on level, sensitivity, and more to ensure there is no erroneous shaking or rattling in your device.
Now let’s take a quick look at the test sequence.
As you can see we have 3 message steps instructing us to start the vibrations, each is followed by a 3 second acquisition step. Once we’ve collected the data, we take an FFT of the waveforms using an analysis step to get the spectra. And post-processing steps are used to get the level vs time and resonant frequencies.
We can also use the same sequence to look at the haptic signatures of various ringtones. For this one, I’m going to use a watch. Again I’ll attach the accelerometer to the back of the device with sticky tack.
This sequence is very similar. On the haptics side I’ve simply renamed the inputs to Ringtones 1, 2 and 3 to make it easier to follow. I’ve also added an SCM measurement microphone to the other input of the AudioConnect, and added a simultaneous audio acquisition step to the sequence.
For this measurement, I’m using my phone’s default watch app, and triggering the acquisition by starting the ringtone.
Let’s start it. I’ll tell the sequence I’m ready, then I’ll use my phone to play the first ringtone on the watch, this one’s called pebbles.
And the second…focus
And the third…. jingle
Let’s take a look at our results…I’m showing all 3 ringtones on the same graph.
On the left hand side we have our haptic analysis. Here you can see we have the raw waveform… the spectrum… and the level vs time for each ringtone. On the right hand side, we show the acoustic waveform and FFT.
So, as you can see, haptic measurements are pretty straightforward in SoundCheck, and can easily be made simultaneously with acoustic measurement.
I hope you found that interesting. If you want to try it out, head on over to our website and download the sequence from the test sequences section under the resources menu.


