Easily measure vibration with accelerometers in SoundCheck! In this quick tip video, we’ll show you how to set up and calibrate an accelerometer for precise vibration measurements.
Additional Resources for SoundCheck
Detailed explanations of how to use SoundCheck can be found in the SoundCheck manual.
Video Transcript: Using Accelerometers with SoundCheck
In this short quick tip video I’ll demonstrate how to use an accelerometer with SoundCheck. This is useful when measuring vibration, not just an acoustic input.
First you need to set your input signal path to accelerometer in the calibration menu and calibrate your input. Accelerometer calibration sequences are built into SoundCheck so it’s simple – just click the calibrate button and it will automatically calibrate your input. I have a B&K 4294 calibrator with a 4534-B-001 accelerometer, which I can select here and then calibrate.
Now let’s take a look at our accelerometer readings. I still have my accelerometer on the calibrator, so it should show me 10 meters per second squared.
You can also integrate the input to view velocity rather than acceleration. We just need to check this ‘integrate’ box here, and now it calculates the velocity in meters per second. This is useful if you want to correlate measurements to velocity rather than acceleration, for example, if you are measuring fan noise at different speeds or as a device ramps up.This calibrator outputs 10 milimeters per second, so if I enable this checkbox that’s what we’ll see.
You can even plot these measurements on a strip chart to see how the velocity is changing over time.
https://www.listeninc.com/wp/media/2025/03/Accelerometers-Blog-TN.png10801080Julius Wijonohttps://www.listeninc.com/wp/media/logo.pngJulius Wijono2025-03-04 05:00:522026-08-27 14:08:00Using Accelerometers with SoundCheck
Effortlessly organize your SoundCheck data with the Memory List! Learn how to protect, autoprotect, and rename data to keep critical measurements safe and accessible during your testing sessions.
Additional Resources for SoundCheck
Detailed explanations of how to use SoundCheck can be found in the SoundCheck manual.
Video Transcript: Organizing SoundCheck Data with the Memory List
By default, when you run a sequence in SoundCheck, previously acquired sequence data in the memory list is overwritten and will be lost unless you configure the sequence to autosave your data.
Today, I’ll demonstrate how to use memory list functions to safeguard your sequence data, ensuring it remains in the memory list until you choose to manually save it, delete it, or close your SoundCheck session.
After running a sequence, I want to preserve the fundamental curve so it’s not overwritten during the next sequence run. To do this, I highlight the fundamental curve, right-click, go down to “Protect Data” in the drop-down menu, and select “Protect.” The protected version of the fundamental curve now appears down here. This checkmark shows it’s no longer sequence data, and the dash “P” indicates it is protected. Now we can remove this piece of protected data from the memory list, and I’ll show you how to autoprotect data.
In this case, I want to autoprotect the fundamental and the THD curve so that every time I run the sequence, it’s automatically protected. Once again, I’m going to hover over the “Protect Data” menu and select “Autoprotect.” The fundamental and THD icons change from rounded shapes to diamonds to indicate the data is autoprotected. Now, every time I run the sequence, the fundamental curve and the THD curve are Autoprotected and remain in the memory list. I’ve run the sequence four times, and you can see four autoprotect instances of the fundamental and THD curves.
Now, if we get rid of these autoprotected curves, and highlight the fundamental and THD curves, I can undo the autoprotection. As you can see, they revert to their traditional circle icons, and upon re-running the sequence again, all of our data will populate.
Lastly, I’ll demonstrate how to protect data by renaming it, including renaming multiple curves simultaneously. I’m going to select fundamental, THD, and then choose the “Rename” option. This prompts the rename dialogue, where I can designate them as “Fundamental 1-2-3”, and “THD 1-2-3. Upon renaming these curves, they also appear in the memory list as protected items.
So that’s 3 methods we can use to retain data in the memory list – Autoprotect, Protect, and Rename. Try it out, and give us a shout if you have any questions.
https://www.listeninc.com/wp/media/2024/11/Memory-List-Blog-TN.png10801080Julius Wijonohttps://www.listeninc.com/wp/media/logo.pngJulius Wijono2024-11-19 00:00:132026-08-27 14:07:25Organizing SoundCheck Data with the Memory List
Create a custom SoundCheck user interface with Python. Watch this video to learn how to integrate sequence selection via TCP/IP commands for efficient testing.
Additional Resources for SoundCheck
Detailed explanations of how to use SoundCheck can be found in the SoundCheck manual.
Video Transcript: Create a Simple SoundCheck User Interface with Python
In this quick demo, I’m going to show you an example of how a Python script can be used to create a custom SoundCheck interface.
Let’s say I have a folder full of SoundCheck sequences and I want to be able to select which sequences to run using a simple interface like this. I used Python to create this GUI, then I integrated it with SoundCheck using the TCP/IP command set that we provide. This comes with comprehensive documentation that outlines all the available functions.
Now, when I run my python script, I’m prompted to select the folder where my sequences are located. I can see all the sequences in that folder, in alphabetical order. Running them is simple, I’ll just select a couple of them, type in the serial number and press the Run button. As you can see, SoundCheck launches and runs those sequences in order, one after the other. This is just a simple example sequence to demonstrate this functionality, but your sequences can be as complex as you want.
I can also make sequence selections via the GUI on the go, for example if I want to decide which sequence to run next based on the outcome of the current sequence.
The GUI can remain open and can be used to run other combinations as well, for example the second sequence in this list. This Python GUI can be used as a template to build your own custom GUIs and is provided free of charge from Listen.
You can find all of these commands within the TCP/IP documentation in your SoundCheck directory. If you would like a copy of this GUI to customize for your own needs, please contact our support team.
https://www.listeninc.com/wp/media/2024/11/Sequence-Selection-GUI-Blog.png10801080Julius Wijonohttps://www.listeninc.com/wp/media/logo.pngJulius Wijono2024-11-05 11:57:212026-08-27 14:00:17Create a Simple SoundCheck User Interface with Python
Easily control the input and output levels of your audio devices using SoundCheck’s Custom Mixer Volume step. In this video, we’ll show how controlling audio device volume for devices like USB headsets ensures accurate calibration and testing.
Additional Resources for SoundCheck
Detailed explanations of how to use SoundCheck can be found in the SoundCheck manual.
Video Transcript: Controlling Audio Device Volume in SoundCheck
In SoundCheck, controlling the input and output levels of audio devices is crucial for consistent calibration and effective testing. The Custom Mixer Volume step allows you to achieve this with any device running on WDM, WASAPI, or Core Audio. For example, you can control the volume of a headset while testing it, or set the levels of a device to unity gain.
Here, I have a USB headset connected, and I want to control its output level in my sequence. In this sequence, I’ll play pink noise through the USB headset and set a specific volume level at the start of the sequence. You can find this step in the Sequence Editor under Custom Mixer Volume. Click and drag it into the sequence steps and double-click to open the Mixer Volume window.
You must set the type as either a playback device or a recording device for volume control. Select the device you wish to adjust; I will be using the USB headset. Then, you can set the volume control. I will set this to 50% and ensure it is unmuted.
When I run the sequence, you will see that the USB headset in my settings changes to the percentage that I just set.
There are a couple of things to be aware of when using this mixer volume step:
Separate steps are required for playback and recording. This means if you need to control both input and output levels, you’ll need two Custom Mixer Volume steps in your sequence.
Separate steps are required for each device being controlled.
This custom step cannot be renamed in a sequence. If you need it labeled, right-click on the step and add a comment to display the name of the device.
https://www.listeninc.com/wp/media/2024/10/Custom-Mixer-Volume-Blog.png10801080Julius Wijonohttps://www.listeninc.com/wp/media/logo.pngJulius Wijono2024-10-23 14:21:242026-08-27 14:01:01Controlling Audio Device Volume in SoundCheck
Highlighting curves in SoundCheck allows you to make specific data stand out on your graphs. Whether comparing multiple curves or focusing on key waveforms, this feature simplifies data analysis.
Additional Resources for SoundCheck
Detailed explanations of how to use SoundCheck can be found in the SoundCheck manual.
Video Transcript: Highlighting Curves in SoundCheck
Curve highlighting is a new feature we introduced in SoundCheck 22 that makes it easy to select any curve on a graph and make it stand out from the rest of the data with a thicker line width. This feature allows users to view specific curves and waveforms more easily in a graph, which is particularly helpful when viewing a batch of data with multiple curves or waveforms.
In this example, I have multiple fundamental curves that I have recorded. You can highlight the curves simply by clicking on them. Control clicking allows selecting multiple curves. Clicking on the Graph legend also selects the curves. You can also highlight multiple curves by right-clicking on the graph window, going to “Highlight Plot”, and selecting the specific curves. Once the curves are highlighted, they are selected in the memory list. This is a great way to read the metadata of selected curves. Click again to remove the highlight.
If you’re in a production environment and you don’t want any changes to the curves, it’s simple to disable this feature – simply edit the display preferences and disable plot highlighting.
https://www.listeninc.com/wp/media/2024/10/Curve-Highlighting-Blog-TN.png10801080Julius Wijonohttps://www.listeninc.com/wp/media/logo.pngJulius Wijono2024-10-08 09:00:522026-08-27 14:20:10Highlighting Curves in SoundCheck
Balance speed and accuracy on your electroacoustic production line using SoundCheck’s confidence limits tools. These tools provide a clear visual display of measurement confidence, which helps you fine-tune your stimulus volume, cycle count, step duration, and frequency range to ensure accurate results with fast throughput.
Additional Resources for SoundCheck
Detailed explanations of how to use SoundCheck can be found in the SoundCheck manual.
Video Transcript: Measuring Confidence Limits
On an electroacoustic production line, faster testing means higher throughput. This makes it desirable to use a short test sweep. However, longer averaging time improves noise rejection leading to more accurate measurements, so how do you reach a good balance between speed and accuracy to get reliable results?
If you are using a stepped sine sweep in SoundCheck, our harmonic track analysis algorithm includes tools to help you find the best combination of speed versus accuracy, like confidence limits, standard error, and noise. Confidence estimates the signal to noise ratio inside the stepped sine filter; the longer the averaging time, the narrower the filter and hence the greater the measurement signal-to-noise ratio.
I’m going to imagine I am testing a loudspeaker on a production line, and I want to get accurate results with the shortest sweep possible.
Let’s check all of these boxes and make a measurement so that we can see how it works.
First let’s take a look at our stepped sine stimulus. Several settings affect its length. I’m sweeping from 20 kHz to 20 Hz using a step sine sweep with R40 resolution, or 12th octave. At each step, I’m sweeping for a minimum of three cycles. The background noise, the signal-to-noise ratio, and the speed of the sweep all affect the measurement confidence. Let’s run this sequence and take a look. We’ll play the stimulus, acquire the data, and analyze it to get a frequency response.
Using tools from harmonic track analysis, I can now look at the fundamental upper and lower confidence limits. These measurements are saved in the memory list, so if I put these on the same graph as my frequency response, I can see that both the upper and lower confidence limits diverge from the frequency response at high and low frequencies.
We can also look at the total noise of the measurement. In this graph, if I use a different color, I can see that at the low end, the environmental noise is actually greater than the measurement so our signal to noise ratio is leading to inaccurate results.
So how can we improve this?
We can try to improve the signal to noise by playing the sweep at a louder volume. I can make sure that I have enough input gain to have a good signal to noise ratio using the max FSD in to make sure we’re at least minus 30 dB. I can also increase my stimulus cycles to reduce the influence of the noise.
Now let’s look at my stimulus step. I’m sweeping from 20 kHz to 20 Hz at R40 resolution, with each step lasting at least three cycles. SoundCheck allows you to define these independently. Here I have 121 steps from 20 Hz to 20 kHz, and each step lasts at least three cycles. I can also set a minimum duration for each step, and the sweep will satisfy both criteria. Increasing the number of cycles or the minimum duration lengthens each step, but improves noise rejection.
If I increase the number of cycles to 20 and set a minimum duration of 20 milliseconds, it will transition at 20 cycles or 20 milliseconds, whichever is longer. At 1000 Hertz, 20 Cycles equals 20 milliseconds so for anything lower 20 Cycles is longer than 20 milliseconds and for anything higher 20 milliseconds is greater than 20 cycles. For example at 20 KHz, 20 Cycles is a very short amount of time so the minimum duration will increase the amount of Cycles to last 20 milliseconds.
Now you can see our original sweep is 2.7 seconds but let’s update it, and now you can see it takes 18 seconds, which might be too long for a production line. To keep it shorter we can make other changes like change the step resolution of the steps from R40 to R10, so the frequency range is the same but we have less steps per octave. Now if we update we can see it shortens the sweep to 5 seconds.
We can also adjust the frequency range based on what we really need to test our device. If we don’t really need to test down to 20 Hz or up to 20k, we could reduce the range to say, 100 Hz to 10kHz. Now you can see this brings the sweep length down to 1 second, which is much more appropriate for a production line test.
Let’s run the sequence again and see what our measurement confidence looks like with these new settings. We can see now the confidence is almost exactly where the frequency response is. It’s diverging a little bit in the low frequencies due to high total noise and because the speaker’s rolling-off a little near 100 Hz.
Let’s try one more tweak. Let’s try 10 cycles instead of 20. Now the sweep is only 680ms long. And if we run it, we can see that the confidence is much less, so maybe we do need to increase the cycles and go with a slightly longer stimulus.
We can continue to optimize our stimulus step using these tools to achieve the best combination for our speed and accuracy requirements.
And one last thing… if your measurement confidence is low due to noise, don’t forget to try to reduce your background noise – this will probably have the biggest effect on your measurement confidence!
https://www.listeninc.com/wp/media/2024/09/Confidence_Limits_Blog_TN.png10801080Julius Wijonohttps://www.listeninc.com/wp/media/logo.pngJulius Wijono2024-09-24 09:00:042026-08-27 14:02:28How to Use Confidence Limits in SoundCheck
Unlock the hidden potential of SoundCheck’s Signal Generator! From keyboard shortcuts to saving custom frequency favorites, we’ll be exploring some of the lesser-known features and capabilities of this virtual instrument.
Additional Resources for SoundCheck’s Signal Generator
Detailed explanations of how to use SoundCheck can be found in the SoundCheck manual.
In this SoundCheck video tip, I’ll demonstrate some of the lesser-known features of the Signal Generator virtual instrument. Many front panel features are obvious, like the signal type dropdown selections, level and frequency fields, signal path selections, and the sample rate selector. But let’s explore some hidden features.
Did you know you can increment the frequency and level values from your keyboard? Pressing the F8 function key highlights the level field. Press it again, and it highlights the frequency field. On the level field, the Page Up and Page Down keys increment the level in 1dB steps. Press F8 again to move to the frequency field. Page Up and Page Down increment the frequency in 1/24 octave steps.
You can set the maximum and minimum output levels and frequencies using these sliders to limit the range of the signal path. This stops you from damaging your speaker with too much voltage or a frequency outside of its passband. Frequency and Level can also be controlled using a USB knob, such as this Drok knob.
Here’s another neat trick: right-click on the frequency numeric field to instantly set a 1 kHz frequency. You can also save and ‘favorite’ specific frequencies. You can see I’ve already saved 345 and 550 Hz. If I now want to also add 268 Hz, I can just add it, and it’s now available in the list. You can also quickly access standard octave frequencies based on the ISO preferred frequencies.
When I change the signal type to noise, the interface changes. You can control the minimum and maximum frequency of the noise, and this checkbox inverts the signal phase by 180 degrees.. You can also apply equalization, if it’s available on your signal path, by checking the EQ checkbox. The noise frequency resolution defaults to 1 Hz, and you can play it continuously, for a specific duration, or a set number of times.
For waveform playback, the interface shows both peak and RMS values. If we load a multi-channel wav file, we can select any channel and get additional information, such as whether it’s mono, stereo, or multi-channel, along with the sample rate and bit depth. Also, note the play start and end control that allows you to play a portion of a wav file or waveform.
At the bottom, there are controls for saving settings so that your configurations can be recalled at any time. You can set your favorite configuration as the default so the generator always opens with these settings, and use the “Save to Memory” button to save the current generator level into the memory list for easy recall.
Lastly, you can minimize or expand the generator, which is useful when you are using multiple generators and need to save screen space. That’s a quick demo of some lesser-known features of the Signal Generator. I hope you learned something new today!
Easily launch multiple virtual instruments in SoundCheck with just a click or a sequence step! In this tutorial, we will demonstrate how to save your virtual instruments configurations as .vic files and seamlessly recall them whenever you need.
Additional Resources for SoundCheck
Detailed explanations of how to use SoundCheck can be found in the SoundCheck manual.
Video Transcript: How to Save Virtual Instruments Configuration Files
In SoundCheck, do you know you can save time launching multiple virtual instruments with a simple click or step in a sequence?
In this example, I have three virtual instruments; a signal generator, a multimeter, and a multi-instrument that I want to recall in the future.
To save this configuration, go to Instruments > Save Configuration As and it will be saved as a .vic file.
This saves not only the combination of instruments you have created, but also the settings in each instrument.
Loading .vic (from instruments)
I can then recall this configuration by going to Instruments > Open Configuration and all the virtual instruments will appear.
You can also open configurations used recently under “Recently opened configurations”
Loading .vic (sequence editor)
I can also recall the configuration in a sequence as an acquisition step. Click and drag the virtual instrument acquisition step in the sequence editor into your sequence steps and double click on it.
Right click and select “Load Configuration file” and select the desired file you wish to import.
When you run the sequence, the virtual instruments will be displayed.
Edit > Preferences > Launch OR Instruments > Startup
Virtual instrument configuration files can also be set to launch automatically when starting up SoundCheck. You can enable this two ways: From the Edit > Preferences window under the launch tab where you can select the configuration file in the dropdown menu OR from the Instruments > Startup Menu
https://www.listeninc.com/wp/media/2024/08/VIC-Files-Blog-TN.png10801080Julius Wijonohttps://www.listeninc.com/wp/media/logo.pngJulius Wijono2024-08-27 10:02:492026-08-27 14:17:45How to Save Virtual Instruments Configuration Files
Quickly input serial numbers, lot numbers, and more by integrating a barcode scanner with SoundCheck. In this video, we demonstrate how easy it is to set up and use.
Additional Resources for SoundCheck
Detailed explanations of how to use SoundCheck can be found in the SoundCheck manual.
Video Transcript: Using Barcode Scanners with SoundCheck
Integrating barcode scanners with SoundCheck allows you to quickly input serial numbers, lot numbers, and other device and test information. Let me show you a quick demo.
Let’s plug my USB barcode scanner into my computer. It shows up as a standard input device. It’s plug and play, and once it’s connected, it’s ready to use. Instead of typing in the serial number, I can now use my barcode reader to capture the serial number on my device, lot number, or test stand location.
It can also be used in a test sequence. Here I have a sequence that stores the serial number, firmware version, and test stand location as metadata. When I run the sequence, It prompts for my device barcode, which is the serial number … barcode scan … lot number … barcode scan … then the chip barcode, which is the firmware version, … barcode scan … and test stand location.
Next, the test runs. Here, we’re measuring the frequency response, impedance, and THD.
Now, let’s check the metadata. When I click the result in the memory list, you can see the serial number, firmware version, and test stand location that we captured using the barcode scanner.
https://www.listeninc.com/wp/media/2024/08/SoundCheck-Tips.png10801080Julius Wijonohttps://www.listeninc.com/wp/media/logo.pngJulius Wijono2024-08-13 01:30:582026-08-27 14:05:57Using Barcode Scanners With SoundCheck
Ensure your display windows remain intact during sequence editing and runs by using the display lock feature. In this video, we demonstrate how to lock and unlock your display using the padlock icon in the memory list.
Additional Resources for SoundCheck
Detailed explanations of how to configure your SoundCheck display can be found in the SoundCheck manual.
Video Transcript: How to Lock Display Windows on SoundCheck
If you want your current display configuration to remain intact during sequence editing and sequence runs, you can lock it. When a display is locked, the layout cannot be changed in any way. Simply click the padlock icon in the memory list to lock and unlock the display. The padlock is green when the display is unlocked and red when locked.
The display lock affects all displays in all sequences. Display elements cannot be closed or resized, and the minimize and maximize buttons are removed from the display headers. New displays can be opened, but any changes to the displays are not saved.
This prevents you from closing the displays and is useful for maintaining your layout during editing and testing. The lock is always on for Technician and Operator access; only users with Engineer level access have the option of toggling the lock on and off.
For more information, refer to the memory list display menu section of the user manual or visit our website.
https://www.listeninc.com/wp/media/2024/07/Display_Windows_Blog_TN.png10801080Julius Wijonohttps://www.listeninc.com/wp/media/logo.pngJulius Wijono2024-07-30 09:45:042026-08-27 14:12:11How to Lock Display Windows on SoundCheck