This sequence measures the frequency response, THD, and L/R balance of Bluetooth smart glasses speakers. After pairing the device with the BQC-4149 and placing it on a HATS, a 1 kHz pilot tone with a 20 kHz–100 Hz Stweep stimulus is played and captured through the ear simulators. The HarmonicTrak algorithm then analyzes the recording to display output performance.
This sequence measures the frequency response of Bluetooth smart glasses microphones. After pairing the device with the BQC-4149 and mounting it on a HATS, a stimulus is played through the mouth simulator and recorded by the microphone. The HarmonicTrak algorithm then analyzes the recording to display the fundamental frequency response.
The purpose of this sequence is to test a Bluetooth headset using a mixture of analog and digital channels. First, a Multitone stimulus is created with SoundCheck, played back over the Bluetooth headset (at 8 kHz) and recorded by a head and torso simulator’s ear (at 44.1 kHz). Then the same Multitone stimulus is played back through the head and torso’s mouth simulator (at 44.1 kHz) and recorded via the Bluetooth headset (at 8 kHz).
Due to inaccuracies of clock frequency, the Bluetooth device playback sampling rate is often slightly different than it is specified. Therefore, in SoundCheck, the Recorded Time Waveforms are frequency shifted to correct for the inaccurate sampling rate. The exact device playback sampling rate is displayed.
This sequence allows you to test devices without an analog input such as smart speakers, tablets, cellphones and MP3 players using SoundCheck’s frequency-based trigger functionality. This method offers improved accuracy over previous level-based triggering, especially in noisy environments. A stimulus WAV file is created in SoundCheck, and copied to the device under test, where it is played and the response recorded in SoundCheck as if the stimulus were played directly from SoundCheck. The stimulus WAV file to be used on the device under test (DUT) may be customized in the stimulus step.
Note that this sequence uses the level-based trigger available in SoundCheck 16.1 and later. If you are using version 16.0 or earlier, please see the level-based trigger sequence.
Final display of Bluetooth Headset Testing Sequence
This Bluetooth Headset testing sequence for SoundCheck measures the send and receive performance of a stereo Bluetooth headset with a built-in microphone using a mixture of analog and digital channels. The left and right earphones are measured simultaneously with a stepped sweep from 20kHz to 20 Hz using two Bluetooth profiles: A2DP and HFP. The mic is measured with a stepped sweep from 8kHz to 100Hz using the HFP profile.
A short 1kHz tone is pre-pended to the test stimulus which serves as a reference tone for resampling and frequency shift operations. Post-processing resampling and frequency shift precisely synchronizes the stimulus and response waveforms prior to analysis. In this case, the HarmonicTrak algorithm is used for frequency and THD analysis. A2DP frequency response and THD curves are displayed on the first display, followed by A2DP & HFP curves superimposed on a subsequent display. Lastly, the Bluetooth headset’s microphone is tested with HFP and its frequency response is shown on the final display along with the previously collected data.
This test sequence performs frequency response and distortion measurements of a Bluetooth speaker using both a wireless Bluetooth and wired stimuli; then compares the results. This sequence is configured for use with a Portland Tool & Die BTC-4149/4148 or BQC-4149/4148 Bluetooth interface.
Initially, the sequence prompts the operator to turn on the Bluetooth device under test and set it to pairing mode. BTC message steps will connect the Bluetooth device (operator selects the device from a list of detected Bluetooth devices) and connects Bluetooth audio. A 1 kHz test tone is transmitted, and if detected, the test sequence proceeds. A stepped sine sweep from 20 kHz to 100 Hz is played wirelessly to the Bluetooth speaker and measured via a calibrated reference mic.
Two post-processing steps convert the sampling rate and alignment of the response, then an analysis step calculates the frequency response and THD. The Bluetooth is disconnected, and the Bluetooth frequency response and THD curves are displayed on graphs. The operator is then prompted to connect the wired analog input into the Bluetooth speaker, and the same measurements are performed using the analog connection. Analog frequency response and THD curves are temporarily displayed on graphs, followed by graphs containing both Bluetooth and analog curves for comparison.
Listen is a global leader in audio measurement and analysis, with over 30 years’ experience developing innovative test methods and algorithms. SoundCheck, our powerful software-based audio analyzer, pairs with our test interfaces, precision microphones, and accessories to offer a complete solution for testing loudspeakers, headphones, microphones, smart devices, communication systems, hearing aids, automotive audio, and more. Trusted by engineers worldwide, Listen delivers the accuracy and flexibility essential for modern audio testing, from the R&D lab to the production line.
CONNECT
