All Test Sequences
These SoundCheck test sequences form a convenient starting point for many common tests, and can easily be adapted for your specific requirements. Most can be downloaded free of charge, but a few for testing to specific standards are for-purchase.
Filter by Application

Loudspeaker Test Sequences
Frequency-Normalized THD Test Sequence
/in Free, Headphone & Headset Sequences, Loudspeaker Sequences, Smart Device Sequences/by Julius WijonoThis sequence measures both conventional Total Harmonic Distortion (THD) and Normalized THD to provide a more accurate representation of a device’s nonlinear behavior. A stimulus is played through the device under test and recorded via a calibrated reference microphone and amplifier signal paths. Conventional THD compares each harmonic to the fundamental at the stimulus frequency, […]
Polar Plot (MDT-4000 Turntable – LAN)
/in Free, Loudspeaker Sequences/by Julius WijonoThis sequence measures the polar response of a loudspeaker in both the vertical and horizontal dimensions using a polar plot. It is designed to work with the Portland Tool & Die MDT-4000 turntable and has all the necessary commands to automatically rotate it via a Local Area Network (LAN) connection. The sequence uses a log […]
Maximum Sound Pressure Level of a Full-Range Loudspeaker (ANSI/CTA 2034-A 2015)
/in Free, Loudspeaker Sequences/by Julius WijonoThis test sequence determines the maximum output capability of an in-home full-range loudspeaker system to the ANSI/CTA 2034-A 2015 standard. This standard uses shaped noise bursts and limits to measure the maximum output of a speaker. This sequence automates what is typically a time-consuming manual process minimizing test time and reducing the possibility of operator […]
Soundbar Measurement over HDMI Connection
/in Free, Loudspeaker Sequences/by ZarinaSoundbar measurement over HDMI is simple in SoundCheck as the WASAPI driver option allows easy connection to the device under test via HDMI. This test sequence is not exclusive to soundbars; it can be used to make audio measurements on any audio device that accepts audio over HDMI (e.g. TV, computer monitor, home theater speakers, […]
Loudspeaker Diaphragm Displacement Measurement Using a Laser
/in Free, Loudspeaker Sequences/by ZarinaThis pre-written test sequence demonstrates how to use a laser and SoundCheck to measure the peak (max and min) displacement of a loudspeaker diaphragm. SoundCheck is easily configured to include a laser signal path, making it simple to correlate diaphragm displacement with electrical impedance and audio artifacts. In this laser displacement measurement, the user is […]
ANSI/CEA 2010-B 2014 Sequence for Subwoofer Maximum SPL
/in Free, Loudspeaker Sequences/by Devin VaillancourtThis sequence measures the maximum peak SPL of a subwoofer according to ANSI/CEA 12010-B 2014. In this test, 1/3 octave band limited tone bursts are presented to the subwoofer across a 3 octave range from 20 Hz to 160 Hz. At each frequency, the stimulus level is increased in +3 dB increments until the harmonic […]
Polar Plot (MDT-4000 Turntable) Sequence
/in Free, Loudspeaker Sequences/by Devin VaillancourtThis sequence measures the polar response of a loudspeaker in both the vertical and horizontal dimensions. It is designed to work with the Portland Tool & Die MDT-4000 turntable, and has all the necessary commands to automatically rotate it via RS-232. The sequence uses a log sweep stimulus with the Time Selective Response algorithm so […]
Loose Particles Sequence
/in Free, Loudspeaker Sequences/by Devin VaillancourtThis sequence demonstrates how to use SoundCheck to detect loose particle defects in loudspeakers. Loose particles typically reveal themselves as randomly spaced impulses, so they may not be detected when performing frequency based measurements such as THD, even though they can be clearly heard as undesirable artifacts. The loose particle algorithm, which is an available […]
Complete Test Sequence
/in Free, Loudspeaker Sequences/by Devin VaillancourtThe purpose of this sequence is to perform a full suite of basic measurements for a loudspeaker. A 500 mV stepped sine sweep from 20 kHz to 50 Hz is played through the speaker and measured via two channels of the audio interface. A calibrated reference microphone is connected to one of the channels, and […]
Measuring Loudspeaker Maximum Linear Sound Levels Using Noise to the AES75-2022 Standard
/in Free, Loudspeaker Sequences/by Devin VaillancourtThe AES75-2022 standard details a procedure for measuring maximum linear sound levels of a loudspeaker system or driver using a test signal called M-Noise. This is a complex procedure with many repetitive steps, which makes it time consuming to implement manually. This sequence automates the entire process, accelerating test time, minimizing operator intervention, and ensuring […]
Polar Plot (Linear X Turntable) Loudspeaker Sequence
/in Free, Loudspeaker Sequences/by Devin VaillancourtThis sequence measures the polar response of a loudspeaker in both the vertical and horizontal dimensions. It is designed to work with the Linear X turntable, and has all the necessary commands to automatically rotate it via RS-232. The sequence uses a log sweep stimulus with the Time Selective Response algorithm so that the measurements […]
Time Selective Response Sequence
/in Free, Loudspeaker Sequences/by Devin VaillancourtThis sequence demonstrates the capabilities of the TSR (Time Selective Response) algorithm in SoundCheck. Using TSR with a log sweep is a very fast and effective method for measuring frequency response and THD of a speaker in a non-anechoic environment. This example plays a quick log sweep from 20 Hz to 20 kHz. An analysis […]
Enhanced Perceptual Rub & Buzz Demo Sequence
/in Free, Loudspeaker Sequences/by ZarinaThis sequence demonstrates how SC20’s new enhanced Perceptual Rub & Buzz algorithm compares to normalized Rub & Buzz and subjective listening. Running this sequence on a batch of good and bad buzzing loudspeakers should help identify by measurement, audibly defective units and where to set production limits. Starting the sequence, the user is asked at […]
Complete End-of-Line Speaker Test (includes ePRB and eLP)
/in Free, Loudspeaker Sequences/by ZarinaThis sequence is an example of the many types of tests that can be performed quickly and simultaneously on a loudspeaker production line. A stepped sine sweep (StweepTM) from 20 kHz to 50 Hz is played through the speaker under test and measured via two channels of the audio interface. A calibrated reference microphone is […]
RT60 Room Acoustics
/in Free, Loudspeaker Sequences/by ZarinaThe RT60 room acoustics sequence measures reverberation time and clarity of a room using multiple microphones to accurately characterize measurement environments. This is important for smart device testing as measurements of both speech recognition and audio output often need to be made in fully characterized rooms with known reverberation times and clarity. The method used […]
Measurement of Stereo Soundfield Parameters
/in For Purchase, Loudspeaker Sequences/by ZarinaThe stereo soundfield sequence measures parameters such as Interaural level difference (ILD) and interaural cross-correlation (IACC) using a Head and Torso Simulator (HATS). The spectrum is measured at each ear and calculates interaural level differences (ILD), spectral balance, delay differences, and interaural cross-correlation (IACC). The measurements are made using different time windows, so that the […]
Anechoic Response of a Loudspeaker Without an Anechoic Chamber: Splice Sequence
/in Free, Loudspeaker Sequences/by ZarinaThis sequence measures the anechoic response of a loudspeaker in an ordinary room using both a near field and time-windowed far field measurement “spliced” together to cover the full bandwidth of the loudspeaker’s response from 20 Hz to 40 kHz. First, the microphone is placed very close to the low frequency driver (less than an inch […]
Triggered Record Using Chirp Trigger and WAV File (Version 17 and later)
/in Audio Electronic Sequences, Free, Generic Test Sequences, Loudspeaker Sequences, Smart Device Sequences/by ZarinaThis test sequence demonstrates SoundCheck’s Triggered Record – Chirp Trigger function for open loop testing of devices without analog inputs such as smart speakers, wearables, smart home devices, tablets and cellphones. A stimulus WAV file is created in SoundCheck and transferred to the device under test, where it is played back and the response recorded […]
Measuring Max SPL versus Frequency
/in Free, Headphone & Headset Sequences, Loudspeaker Sequences/by ZarinaThis sequence measures the Max SPL of a transducer versus frequency that a device can play back with acceptable distortion. It is particularly valuable for designers using DSP algorithms to optimize the performance of their speakers. It characterizes the Max SPL of a transducer by setting limits on specific metrics (THD, Rub & Buzz, Perceptual […]
Triggered Record Using WAV File (Version 16.1 and later)
/in Audio Electronic Sequences, Free, Generic Test Sequences, Loudspeaker Sequences, Wireless (Bluetooth) Sequences/by ZarinaThis sequence allows you to test devices without an analog input such as smart speakers, tablets, cellphones and MP3 players using SoundCheck’s frequency-based trigger functionality. This method offers improved accuracy over previous level-based triggering, especially in noisy environments. A stimulus WAV file is created in SoundCheck, and copied to the device under test, where it […]
Smart Speaker Embedded Microphone Test Sequence
/in Free, Loudspeaker Sequences, Microphone Sequences, Smart Device Sequences/by ZarinaThis sequence demonstrates a method by which SoundCheck can measure the performance of a microphone embedded in a so-called “smart speaker.” This smart speaker embedded microphone test assumes that the DUT is an Amazon Echo, but it can be adapted for use with virtually any other type of smart speaker by substituting the Echo’s voice […]
Smart Speaker – Embedded Loudspeaker Test Sequence
/in Free, Loudspeaker Sequences, Smart Device Sequences/by ZarinaThis sequence demonstrates a method by which SoundCheck can measure the performance of a loudspeaker embedded in a so-called “smart speaker”. This example assumes that the DUT is an Amazon Echo but it can be adapted for use with virtually any other type of smart speaker by substituting the Echo’s voice activation phrase audio file […]
Comparison of Wired and Wireless (Bluetooth) Speaker Response
/in Free, Loudspeaker Sequences, Wireless (Bluetooth) Sequences/by ZarinaThis test sequence performs frequency response and distortion measurements of a Bluetooth speaker using both a wireless Bluetooth and wired stimuli; then compares the results. This sequence is configured for use with a Portland Tool & Die BTC-4149/4148 or BQC-4149/4148 Bluetooth interface. Initially, the sequence prompts the operator to turn on the Bluetooth device under […]
Triggered Record Using WAV File (Version 16.0 and earlier)
/in Audio Electronic Sequences, Free, Loudspeaker Sequences/by ZarinaThis sequence allows you to test devices without an analog input such as tablets, cellphones and MP3 players. A stimulus WAV file is created in SoundCheck, and copied to the device under test, where it is played and the response recorded in SoundCheck as if the stimulus were played directly from SoundCheck. The stimulus WAV […]
Thiele-Small Parameters
/in Free, Loudspeaker Sequences/by ZarinaLoudspeaker system performance can be quantitatively related to a set of electro-mechanical parameters. These parameters are known in the industry as Thiele-Small parameters. They were first introduced by A.N.Thiele and Richard H.Small in a series of famous articles published in the 1971-72 Journal of AES (Audio Engineering Society). Over the years these parameters have become […]
Impedance Measurement – Dual Channel Method Using Math Post-Processing
/in Free, Loudspeaker Sequences/by ZarinaThis sequence demonstrates an alternative to the traditional SoundCheck single channel impedance measurement method. A stepped sine sweep from 20 Hz to 20 kHz is played through the speaker while the signal across the loudspeaker terminals is recorded by Direct In 1 and the signal across the sense resistor (impedance box) is recorded by Direct […]
Perceptual Rub & Buzz
/in Free, Loudspeaker Sequences/by ZarinaThis sequence uses the CLEAR algorithm for perceptual Rub & Buzz measurement to detect AUDIBLE Rub & Buzz. It uses a simplified auditory perceptual model to measure the loudness of Rub & Buzz distortion in phons rather than the more traditional dB SPL and % distortion units. These better identify whether distortion due to manufacturing […]
Impedance Measurement – Dual Channel Method Using Transfer Function
/in Free, Loudspeaker Sequences/by radarThis sequence demonstrates an alternative to the traditional SoundCheck single channel impedance measurement method. A pink noise stimulus (10Hz – 10kHz) is played through the speaker while the signal across the amplifier terminals is recorded by Direct In 1 and the signal across the sense resistor is recorded by Direct In 2. A transfer function […]
Headphone and Headset Test Sequences
Frequency-Normalized THD Test Sequence
/in Free, Headphone & Headset Sequences, Loudspeaker Sequences, Smart Device Sequences/by Julius WijonoThis sequence measures both conventional Total Harmonic Distortion (THD) and Normalized THD to provide a more accurate representation of a device’s nonlinear behavior. A stimulus is played through the device under test and recorded via a calibrated reference microphone and amplifier signal paths. Conventional THD compares each harmonic to the fundamental at the stimulus frequency, […]
VR Headset Leakage Measurement Sequence
/in Free, Headphone & Headset Sequences/by Devin VaillancourtVR headset leakage measurement is a useful parameter for VR headset characterization. While they are sometimes connected to headphones, most VR headsets also contain built-in speakers, often on the strap close to the ear. These small speakers often have considerable audio leakage due to their positioning on the band, where there is some transmission through […]
Bluetooth Headset Test Sequence
/in Free, Headphone & Headset Sequences, Wireless (Bluetooth) Sequences/by Devin VaillancourtThe purpose of this sequence is to test a Bluetooth headset using a mixture of analog and digital channels. First, a Multitone stimulus is created with SoundCheck, played back over the Bluetooth headset (at 8 kHz) and recorded by a head and torso simulator’s ear (at 44.1 kHz). Then the same Multitone stimulus is played […]
Headphone Test Sequence
/in Headphone & Headset Sequences/by Devin VaillancourtThis headphone test sequence measures a stereo headphone. Both left and right earphones are measured simultaneously using a standard 1/12th Octave stepped-sine sweep from 20 Hz to 20 kHz. The analysis is then performed using Listen’s HarmonicTrak™ algorithm that measures harmonic distortion and fundamental frequency response simultaneously. Then the diffuse-field and free-field corrected Fundamentals are […]
Measuring Hearing Protection Devices to ANSI S3.19-1974 Standard
/in Free, Headphone & Headset Sequences/by ZarinaThis sequence is used to measure the NRR, or Noise Reduction Rating, of a hearing protection device to the ANSI S3.19-1974 standard. NRR is a numerical representation of the sound attenuation of a device. The sequence first measures the response spectrum of the unoccluded hearing protector test fixture, then makes a second measurement with the […]
Prediction of Listener Preference of In-Ear Headphones (Harman Model)
/in Free, Headphone & Headset Sequences/by ZarinaThis sequence, inspired by AES papers on statistical models to predict listener preference by Sean E. Olive, Todd Welti, and Omid Khonsaripour of Harman International, applies the Harman target curve for in-ear, on-ear and over-ear headphones to a measurement made in SoundCheck to yield the predicted user preference for the device under test. The measurements […]
Measuring Max SPL versus Frequency
/in Free, Headphone & Headset Sequences, Loudspeaker Sequences/by ZarinaThis sequence measures the Max SPL of a transducer versus frequency that a device can play back with acceptable distortion. It is particularly valuable for designers using DSP algorithms to optimize the performance of their speakers. It characterizes the Max SPL of a transducer by setting limits on specific metrics (THD, Rub & Buzz, Perceptual […]
Background Noise Simulation to ETSI ES 202 396-1 Standard
/in For Purchase, Generic Test Sequences, Headphone & Headset Sequences/by ZarinaThis Background Noise Simulation sequence follows the ETSI ES 202 396-1 standard. It will automatically calibrate a standardized 4.1 speaker / subwoofer setup in accordance to the ETSI ES 202 396-1 standard “Loudspeaker Setup for Background Noise Simulation” and provide an equalized, calibrated playback solution to stress your device in a standardized and repeatable way. […]
Bluetooth Headset Testing
/in Free, Headphone & Headset Sequences, Wireless (Bluetooth) Sequences/by ZarinaThis Bluetooth Headset testing sequence for SoundCheck measures the send and receive performance of a stereo Bluetooth headset with a built-in microphone using a mixture of analog and digital channels. The left and right earphones are measured simultaneously with a stepped sweep from 20kHz to 20 Hz using two Bluetooth profiles: A2DP and HFP. The […]
Lightning Headphone Test (Open Loop Headphone Test)
/in Free, Headphone & Headset Sequences/by ZarinaThis sequence tests a stereo headphone connected to a portable audio device such as a mobile phone or MP3 player. This open loop headphone test is particularly useful for testing headphones with proprietary connectors such as the Lightning connector which otherwise can’t be tested in a conventional “closed loop” test configuration. The test stimulus is […]
Headphone Testing with SoundCheck ONE
/in Free, Headphone & Headset Sequences/by ZarinaThis SoundCheck ONE template sequence contains all the essential steps for basic headphone measurements using SoundCheck ONE and AudioConnectTM. The sequence can be easily customized and saved for specific products by turning individual measurements on and off, and by adjusting settings within each sequence step such as stimulus range and level, tolerance limits, graphical displays, […]
IEC-60268-7 Headphone Sequences
/in Free, Headphone & Headset Sequences/by ZarinaIEC-60268-7: Sound System Equipment – Part 7: Headphones and Earphones is an international standard intended to characterize the performance of headphones and earphones. The standard itself is a lengthy document, 9 Sections and 3 Annexes covering 46 printed pages. These SoundCheck sequences focus on the electro-acoustic tests which are detailed in Section 8 “Characteristics to […]
EN 50332-1 – Max. SPL of Portable Audio Devices
/in Audio Electronic Sequences, For Purchase, Headphone & Headset Sequences/by ZarinaThis sequence follows the test standard detailed in EN50332-1 (2013) for measuring the maximum sound pressure for portable music players and the earphones/headphones they are bundled with. The test involves loading a weighted pink noise stimulus file (as specified by IEC 268) onto the portable device and playing it through the earphones at the player’s […]
Active Noise-Cancelling Headphone Battery Life Test
/in Blog, Free, Headphone & Headset Sequences/by ZarinaThis SoundCheck test sequence measures the performance characteristics of Active Noise Cancelling headphones (ANC headphones) while monitoring the DC voltage and current provided to the headphone by its batteries. The sequence first measures the passive attenuation of the headphone before moving into a loop. The loop plays a 2 minute pink noise stimulus at high […]
EN-50332-2: Measuring SPL of Portable Devices
/in Audio Electronic Sequences, For Purchase, Headphone & Headset Sequences/by ZarinaThese two sequences follow the test standard detailed in EN50332-2 for measuring the maximum levels of portable music players and earphones/headphones. This section of the standard covers the individual testing of the devices rather than the combined testing that is detailed in part 1. Note that the physical setup and connections will be different between […]
Headphone Active Noise Cancellation Test Sequence
/in Blog, Free, Headphone & Headset Sequences/by ZarinaThis SoundCheck test sequence measures headphone active noise cancellation (ANC). It measures both the active and passive noise cancellation and calculates total attenuation over the operating frequency range of the headphones. Passive Attenuation is the amount of noise that is reduced at the ear simply by the headphones being worn. Active Attenuation is the amount […]
Microphone Test Sequences
Interchannel Phase
/in Free, Microphone Sequences/by Julius WijonoWhen measuring multiple inputs, for example testing a beamforming microphone array, it can be useful to measure the phase response in reference to a single microphone in the array. This measurement is called interchannel phase. In this sequence, a six microphone array is measured. The user can select a reference microphone (defaulted in this sequence […]
Microphone Frequency Response and Sensitivity Test Sequence
/in Free, Microphone Sequences/by Devin VaillancourtThis is sequence is a basic example of the two most common microphone measurements: frequency response and sensitivity. A stepped sine sweep is played from 10 kHz to 100 Hz through a source that has previously been calibrated to produce 1 Pascal across the frequency band. The recorded signal is analyzed with a Heterodyne analysis […]
Microphone Polar Plot Substitution Method Using Outline ET250-3D
/in Free, Microphone Sequences/by Devin VaillancourtThis sequence measures the directional response of a microphone and graphs the result as a microphone polar plot. A log sweep stimulus is played from 100 Hz to 10 kHz at each angular increment, and the acquired waveform is analyzed using the Time Selective Response algorithm. This method allows the test to be performed in […]
MEMS Microphone Test: Measuring Digital MEMS Microphones – Frequency, Sensitivity, and Power Supply Rejection (PSR) Performance
/in Free, Microphone Sequences/by Devin VaillancourtThis MEMS microphone test suite contains 3 sequences to enable comprehensive testing of digital MEMS microphones: Measurement of frequency and sensitivity using a calibrated source Measurement of frequency using the ‘substitution method’, a solution for measuring frequency response where the source speaker cannot or is not equalized Measurement of power supply rejection (PSR) performance More
Microphone Acoustic Overload Point (AOP)
/in Free, Microphone Sequences/by ZarinaThis sequence measures the microphone acoustic overload point (AOP) – the SPL required to produce 10% THD @ 1kHz from the microphone’s output. A 1 kHz amplitude sweep from a calibrated source speaker is applied across a range from 120 dB SPL to 135 dB SPL.The recorded time waveform is then analyzed using the HarmonicTrak […]
Microphone SNR Measurement (Background Noise Method)
/in Free, Microphone Sequences/by ZarinaThis sequence characterizes a microphone’s ability to passively and/or actively reject noise in the user’s environment. Unlike traditional microphone SNR measurement methods, which calculate a ratio based upon a reference signal and the microphone’s noise floor, this method utilizes a signal (speech played from a mouth simulator) and noise (background noise played from two or […]
Microphone Polar Plot: Substitution Method Using LinearX LT360 Turntable
/in Free, Microphone Sequences/by ZarinaThis sequence measures the directional response of a microphone and graphs the result as a polar plot. A log sweep stimulus is played from 100 Hz to 10 kHz at each angular increment, and the acquired waveform is analyzed using the Time Selective Response algorithm. This method allows the test to be performed in a […]
Smart Speaker Embedded Microphone Test Sequence
/in Free, Loudspeaker Sequences, Microphone Sequences, Smart Device Sequences/by ZarinaThis sequence demonstrates a method by which SoundCheck can measure the performance of a microphone embedded in a so-called “smart speaker.” This smart speaker embedded microphone test assumes that the DUT is an Amazon Echo, but it can be adapted for use with virtually any other type of smart speaker by substituting the Echo’s voice […]
Open Loop Microphone Test
/in Free, Microphone Sequences, Smart Device Sequences/by ZarinaThis sequence demonstrates the two most common microphone measurements, frequency response and sensitivity, on a microphone embedded in a recording device. Typically, when measuring a microphone, the response of the device can be captured simultaneously with the stimulus. However, with devices such as voice recorders and wireless telephones, forming a closed loop can be cumbersome […]
Measuring Digital MEMS Microphones: Frequency, Sensitivity and Power Supply Rejection (PSR) Performance
/in Free, Microphone Sequences/by ZarinaThis test suite contains 3 sequences to enable comprehensive testing of digital MEMS microphones. The first measures the frequency and sensitivity and displays two graphs: absolute level in dBFS, and the same response curve but normalized to 0 dB at 1 kHz. The second sequence uses the substitution method to test a digital MEMS microphone […]
Microphone Polar Plot Sequence
/in Free, Microphone Sequences/by ZarinaThis sequence measures the directional response of a microphone and graphs the result as a polar plot. A log sweep stimulus is played from 100 Hz to 10 kHz at each angular increment, and the acquired waveform is analyzed using the Time Selective Response algorithm. This method allows the test to be performed in a […]
Microphone Self Noise Measurement Test
/in Free, Microphone Sequences/by ZarinaThe purpose of this sequence is to perform a microphone self noise measurement for a condenser microphone. To do this, we use the spectrum analysis step and a power sum calculation to derive an RMS rating for the unit under test. The sequence has several parts, a few of which are optional. The first section […]
Telephone Test Sequences
USB Headset Input/Output Test Sequence
/in Communications Sequences, Free/by Renee LucasThe purpose of these sequences is to test the left and right earphone outputs as well as the microphone input of a USB headset. Because SoundCheck supports both analog and digital interfaces, the headset simply plugs into a computer USB port and configures as a digital channel to be tested like a conventional device. For […]
Tonal Noise (Send Path) Sequence
/in Communications Sequences, Free/by Renee LucasThis sequence measures single-frequency interference (tonal noise) in the send path of a communication device to ensure compliance with the Microsoft Teams Audio Test Specification (Section 6.6). A calibrated mouth simulator plays an IEEE Male speech stimulus at 94 dBSPL followed by a period of silence, which is recorded through the device under test. The […]
Tonal Noise (Receive Path) Sequence
/in Communications Sequences, Free/by Renee LucasThis sequence measures single-frequency interference (tonal noise) in the receive path of a communication device to ensure compliance with the Microsoft Teams Audio Test Specification (Section 6.13). The sequence plays and records a test signal containing digital silence directly through the device under test to detect potential narrow-band impairments caused by internal electrical, fan, or […]
Receive Loudness Rating with ITU Real Speech Test Sequence
/in Communications Sequences, Free/by Devin VaillancourtThe purpose of this sequence is to measure the Receive Loudness Rating (RLR) following the ITU-T P.79 standard using a Head and Torso Simulator (HATS). First, real speech from the ITU-T P.501 standard is sent to the Device Under Test (DUT) speaker by an electrical interface. The HATS right ear captures the DUT‟s speaker response. […]
Send Loudness Rating with ITU Real Speech Test Sequence
/in Communications Sequences, Free/by Devin VaillancourtThe purpose of this sequence is to measure the Send Loudness Rating (SLR) following the ITU-T P.79 standard. This sequence can be used with handsets, headsets, and conference call devices. First, real speech from the ITU-T P.501 standard is played out of a mouth simulator. The Device Under Test (DUT) microphone then captures the signal […]
TIA-5050 Test Sequence for Narrowband (NB) and Wideband (WB) Mobile Handset Phones
/in Communications Sequences, For Purchase/by ZarinaTIA 5050 is a US standard with measurement methods and requirements for the receive volume control performance of both narrowband (NB) and wideband (WB) mobile handset phones. The measurements include conversational gain, frequency response, and distortion. Measurements are made at both 2N and 8N handset application forces, with different requirements applied to each. Either Free […]
TIA 920-B Sequence for Measurement of Narrowband and Wideband Digital Phones
/in Communications Sequences, For Purchase/by ZarinaTIA 920-B is a comprehensive US dual-bandwidth standard that applies to both narrowband (NB) and wideband (WB) devices. It also allows a choice between Free Field (FF) and Diffuse Field (DF) as the Listener Reference Point (LRP). These sequences measure digital communications devices with handset features according to TIA-920.110-B, speakerphones according to TIA-920.120-B, and headsets […]
Hearing Aid Compatibility to TIA 1083 and FCC Part 68.316
/in Communications Sequences, For Purchase/by ZarinaThese two test sequences are designed to test the hearing aid compatibility of a telephone according to the TIA 1083 and FCC Part 68.316 standards. These sequences, which rely on the user having radial and axial HAC probes, play the appropriate test signals, measure the response and compare them to the limits in the standard. […]
TIA-920-A Sequence for Wideband Digital Phones
/in Communications Sequences, For Purchase/by ZarinaThis sequence has been superseded by TIA 920-B test sequence. More
TIA-810-B Standard for Narrowband Digital Phones
/in Communications Sequences, For Purchase/by ZarinaThis sequence has been superseded by the TIA 920-B test sequence. More
Wireless (Bluetooth) Test Sequences
Smart Glasses Speaker Output Test Sequence
/in Free, Smart Device Sequences, Wireless (Bluetooth) Sequences/by Julius WijonoThis sequence measures the frequency response, THD, and L/R balance of Bluetooth smart glasses speakers. After pairing the device with the BQC-4149 and placing it on a HATS, a 1 kHz pilot tone with a 20 kHz–100 Hz Stweep stimulus is played and captured through the ear simulators. The HarmonicTrak algorithm then analyzes the recording […]
Smart Glasses Mic Input Test Sequence
/in Free, Smart Device Sequences, Wireless (Bluetooth) Sequences/by Julius WijonoThis sequence measures the frequency response of Bluetooth smart glasses microphones. After pairing the device with the BQC-4149 and mounting it on a HATS, a stimulus is played through the mouth simulator and recorded by the microphone. The HarmonicTrak algorithm then analyzes the recording to display the fundamental frequency response. More
Bluetooth Headset Test Sequence
/in Free, Headphone & Headset Sequences, Wireless (Bluetooth) Sequences/by Devin VaillancourtThe purpose of this sequence is to test a Bluetooth headset using a mixture of analog and digital channels. First, a Multitone stimulus is created with SoundCheck, played back over the Bluetooth headset (at 8 kHz) and recorded by a head and torso simulator’s ear (at 44.1 kHz). Then the same Multitone stimulus is played […]
Triggered Record Using WAV File (Version 16.1 and later)
/in Audio Electronic Sequences, Free, Generic Test Sequences, Loudspeaker Sequences, Wireless (Bluetooth) Sequences/by ZarinaThis sequence allows you to test devices without an analog input such as smart speakers, tablets, cellphones and MP3 players using SoundCheck’s frequency-based trigger functionality. This method offers improved accuracy over previous level-based triggering, especially in noisy environments. A stimulus WAV file is created in SoundCheck, and copied to the device under test, where it […]
Bluetooth Headset Testing
/in Free, Headphone & Headset Sequences, Wireless (Bluetooth) Sequences/by ZarinaThis Bluetooth Headset testing sequence for SoundCheck measures the send and receive performance of a stereo Bluetooth headset with a built-in microphone using a mixture of analog and digital channels. The left and right earphones are measured simultaneously with a stepped sweep from 20kHz to 20 Hz using two Bluetooth profiles: A2DP and HFP. The […]
Comparison of Wired and Wireless (Bluetooth) Speaker Response
/in Free, Loudspeaker Sequences, Wireless (Bluetooth) Sequences/by ZarinaThis test sequence performs frequency response and distortion measurements of a Bluetooth speaker using both a wireless Bluetooth and wired stimuli; then compares the results. This sequence is configured for use with a Portland Tool & Die BTC-4149/4148 or BQC-4149/4148 Bluetooth interface. Initially, the sequence prompts the operator to turn on the Bluetooth device under […]
Automotive Test Sequences
In-Car Audio Measurements
/in Automotive Sequences, Free/by Devin VaillancourtThis in-car audio test sequence measures the transient distortion (also known as buzz, squeak, and rattle, Rub & Buzz, or impulsive distortion), frequency response, and maximum sound pressure level of a vehicle infotainment system to the methods outlined in the Audio Engineering Society Technical Committee on Automotive Audio (TC-AA) in-vehicle measurements draft white paper. The […]
Automotive Max SPL (Maximum Sound Pressure Level)
/in Automotive Sequences, Free/by ZarinaThis sequence measures Automotive Max SPL, the Maximum Sound Pressure Level (SPL) of a car infotainment system in the vehicle’s interior. It calculates a single value for Max SPL and displays the Max SPL Spectrum, showing the six individual microphone responses plus the average curve. The sequence uses a 6 microphone array mounted at either […]
Triggered Record Using WAV File and 6 Mic Array
/in Automotive Sequences, Free/by ZarinaThis sequence allows you to measure a playback system without analog inputs using a 6 microphone array. Specifically, the sequence is designed to measure an in-car audio system. A stimulus WAV file is created in SoundCheck and transferred to the device under test (DUT) where it is played back and the response captured by SoundCheck […]
Hearing Aid Test Sequences
ANSI S3.22 Hearing Aid Test Sequences
/in For Purchase, Hearing Aid Sequences/by ZarinaThese sequences include all the tests from ANSI S3.22:2014 as well as some of the additional ‘Annex C’ tests from the 2014 ANSI standard. This guide describes the basic functionality of each sequence and details the process of hardware setup and calibration. Each test, as outlined in the standards, is contained in a single test […]
Smartphone and Tablet Test Sequences
Nothing Found
Sorry, no posts matched your criteria
Audio Electronic Test Sequences
Amplifier THD+N Sequence
/in Audio Electronic Sequences, Free/by Devin VaillancourtThis sequence measures an audio amplifier’s Frequency Response, Gain, THD, THD+Noise, and Self-noise. It accomplishes this by playing a 1/3rd octave sine sweep through the amplifier. A HarmonicTrak™ analysis step calculates the fundamental frequency response curve as well as the distortion plots. The sequence then records and analyzes a spectrum of the amplifier’s self-noise. More
MP3 Player (Multitone) Sequence
/in Audio Electronic Sequences, Free/by Devin VaillancourtThe principle is first to create a multitone stimulus waveform with SoundCheck and transfer it to the MP3 Player to be tested. This waveform is then played back, to be acquired and analyzed by SoundCheck. Both Left and Right channels are acquired at once. The acquisition is made easy by using a trigger on one […]
Triggered Record Using Chirp Trigger and WAV File (Version 17 and later)
/in Audio Electronic Sequences, Free, Generic Test Sequences, Loudspeaker Sequences, Smart Device Sequences/by ZarinaThis test sequence demonstrates SoundCheck’s Triggered Record – Chirp Trigger function for open loop testing of devices without analog inputs such as smart speakers, wearables, smart home devices, tablets and cellphones. A stimulus WAV file is created in SoundCheck and transferred to the device under test, where it is played back and the response recorded […]
Triggered Record Using WAV File (Version 16.1 and later)
/in Audio Electronic Sequences, Free, Generic Test Sequences, Loudspeaker Sequences, Wireless (Bluetooth) Sequences/by ZarinaThis sequence allows you to test devices without an analog input such as smart speakers, tablets, cellphones and MP3 players using SoundCheck’s frequency-based trigger functionality. This method offers improved accuracy over previous level-based triggering, especially in noisy environments. A stimulus WAV file is created in SoundCheck, and copied to the device under test, where it […]
Triggered Record Using WAV File (Version 16.0 and earlier)
/in Audio Electronic Sequences, Free, Loudspeaker Sequences/by ZarinaThis sequence allows you to test devices without an analog input such as tablets, cellphones and MP3 players. A stimulus WAV file is created in SoundCheck, and copied to the device under test, where it is played and the response recorded in SoundCheck as if the stimulus were played directly from SoundCheck. The stimulus WAV […]
EN 50332-1 – Max. SPL of Portable Audio Devices
/in Audio Electronic Sequences, For Purchase, Headphone & Headset Sequences/by ZarinaThis sequence follows the test standard detailed in EN50332-1 (2013) for measuring the maximum sound pressure for portable music players and the earphones/headphones they are bundled with. The test involves loading a weighted pink noise stimulus file (as specified by IEC 268) onto the portable device and playing it through the earphones at the player’s […]
EN-50332-2: Measuring SPL of Portable Devices
/in Audio Electronic Sequences, For Purchase, Headphone & Headset Sequences/by ZarinaThese two sequences follow the test standard detailed in EN50332-2 for measuring the maximum levels of portable music players and earphones/headphones. This section of the standard covers the individual testing of the devices rather than the combined testing that is detailed in part 1. Note that the physical setup and connections will be different between […]
Linear Motor Test Sequences
Linear Motor Test Sequence
/in Free, Linear Motor Test Sequences/by ZarinaLinear motors (also known as linear vibrators or linear resonant actuators) have become increasingly popular in handheld devices such as phones and tablets for providing haptic feedback to the device’s user. The typical linear motor design uses a fixed voice coil in conjunction with a moving magnetic mass. A spring is placed between the mass […]
General (non-application-specific) Test Sequences
External Calibration of a Reference Speaker
/in Free, Generic Test Sequences/by Julius WijonoThis sequence calibrates a reference speaker by automatically adjusting its response against a target curve, eliminating the need to step through the calibration editor. It runs using the “Reference Mic” input and “Source Speaker.dat” output device, providing fast and consistent calibration with a single sequence run. To use different signal paths or devices, the calibration […]
Finding the test level in volts to achieve a desired SPL
/in Free, Generic Test Sequences/by ZarinaThis sequence finds the test level (volts) to achieve a desired sound pressure level (dB SPL). The user enters the desired sound pressure level. 1 volt is played through the amplifier which is used to then calculate the appropriate voltage level to obtain the desired Sound pressure level. The sequence then runs a stepped sine […]
Comparison of Effect of Different Masks on Speech Distortion
/in Free, Generic Test Sequences/by ZarinaThe purpose of this sequence is to compare the response of an artificial mouth when face masks of different construction are mounted on the mouth. The sequence assumes a lightweight disposable mask and a heavy multi-layer cloth mask. A stepped sinewave from 10 kHz – 100 Hz is played from the unoccluded mouth and the […]
Waveform Windowing
/in Free, Generic Test Sequences/by ZarinaThis sequence demonstrates how SoundCheck’s Windowing post-processing function is applied to waveforms to remove measurement artifacts that might otherwise create false auto delay values and subsequent analysis errors. This sequence uses data from a customer who was measuring the directivity of a hearing aid-type device by mounting it on a rotating HATS and using a […]
External Control of SoundCheck via TCP/IP
/in Free, Generic Test Sequences/by ZarinaTCP/IP control of SoundCheck provides a powerful and expandable command format for controlling and interacting with SoundCheck via any programming language (C#, C++, MATLAB, VB.net, LabVIEW, Python, etc.), on any operating system, either locally or through a network. This is valuable for anyone wishing to control SoundCheck from an external program, e.g. as part of an […]
Triggered Record Using Chirp Trigger and WAV File (Version 17 and later)
/in Audio Electronic Sequences, Free, Generic Test Sequences, Loudspeaker Sequences, Smart Device Sequences/by ZarinaThis test sequence demonstrates SoundCheck’s Triggered Record – Chirp Trigger function for open loop testing of devices without analog inputs such as smart speakers, wearables, smart home devices, tablets and cellphones. A stimulus WAV file is created in SoundCheck and transferred to the device under test, where it is played back and the response recorded […]
Triggered Record Using WAV File (Version 16.1 and later)
/in Audio Electronic Sequences, Free, Generic Test Sequences, Loudspeaker Sequences, Wireless (Bluetooth) Sequences/by ZarinaThis sequence allows you to test devices without an analog input such as smart speakers, tablets, cellphones and MP3 players using SoundCheck’s frequency-based trigger functionality. This method offers improved accuracy over previous level-based triggering, especially in noisy environments. A stimulus WAV file is created in SoundCheck, and copied to the device under test, where it […]
Background Noise Simulation to ETSI ES 202 396-1 Standard
/in For Purchase, Generic Test Sequences, Headphone & Headset Sequences/by ZarinaThis Background Noise Simulation sequence follows the ETSI ES 202 396-1 standard. It will automatically calibrate a standardized 4.1 speaker / subwoofer setup in accordance to the ETSI ES 202 396-1 standard “Loudspeaker Setup for Background Noise Simulation” and provide an equalized, calibrated playback solution to stress your device in a standardized and repeatable way. […]














































